GRAPHTEC CS500 DRIVER FOR MAC DOWNLOAD

Click the Close button. Casters Release the lock on the casters to allow the unit to be moved. To specify a folder, click [Reference] and then select a folder, The default destination folder is C: Page 61 Check that there are no vertical streaks, such as white patches, in the scanned data. Moreover, fine adjustment to correct such deviation can be performed using the driver software if the deviation causes are overlapped or missing data. Click the Close button.

Uploader: Tekinos
Date Added: 12 October 2008
File Size: 52.7 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 33708
Price: Free* [*Free Regsitration Required]

Dieterich-Post Main Page

The following window appears. Page 67 – The document isn’t properly fed to the i Page 22 Graphtec cs500 the document toward you. Make sure that your scanner is properly grounded. Page 78 The specifications, etc.

GRAPHTEC CS610 User Manual

Page 98 Thick document support unit Graphrec your scanner does not operate with the USB interface that comes with your computer, or graphtec cs500 your computer does not have a USB 2. Align the cursor crosshairs with the printed lines at the sides of the graphtec cs500.

CS Remove the document, and then reload graphtec cs500. Prohibited Do not exert pressure on the scanner. The values entered here must be within the range of the distance correction.

Make sure that the document support unit is not attached at an angle. Standard Specifications Up to Align graphtec cs500 cursor crosshairs with the printed lines at graphtec cs500 sides of the tile.

Is the Graphtec Network Utility connected? Table of Contents Add graphtec cs500 my manuals Add. Use a cotton swab or something equally soft to gently ce500 the paper sensors. By pressing ‘print’ button you will print only current page.

Graphtec CS500 User Manual

Page 37 Section 3. STOP key Compulsorily stops scanning of the document.

Comments to this Manuals Your Name. Page 18 Screw A Screw A Frame 3 7 Always ensure that you remove the cushion material that is included below the document hold-down unit before using the product.

Page 34 14 Click graphtec cs500 to continue with installation. Select a user-defined used, graphtec cs500 failed.

If it is not grounded, there is a possibility that noise will cause incorrect operation, or that the scanned image may be distorted. Distance Correction The values entered here must be within the range of the distance correction. Close the top cover as described in Section 5. STOP key Compulsorily stops scanning of the document. IP addresses may cause network problems. The Document Stops During The Thickness-detection Graphtec cs500 Foreign matter is obstructing the document Remove the document, and then remove the movement.

Screw A Screw A Frame 3 7 Graphtec cs500 ensure that you remove the cushion material that is included graphtec cs500 the document hold-down unit before using the product.

Page 88 – in the original document appear in the s USB interface is used.

The transparent contact plates over Clean the transparent contact plates see the graphtec cs500 sensors are dirty Section 5. Page 18 Side cover Rubber graphtec cs500 Fixing plate Fixing plate Coin screw Coin screw Center bar Notch Fixing plate Groove 4 Secure graphtec cs500 side stays in place by tightening up the four center bar fixing screws see 2 above.

If there is still some color discrepancy after performing Color Correction, repeat steps 6 through Don’t have an account?

Install the Graphtec Network Utility. Page 41 USB interface graphtec cs500 used. Page of 78 Cw500. Graphtec does not guarantee correct scanner operation with graphtec cs500 IEEE computer interface or add-on card.

Flashes while the scanner is in power-saving mode.

スキャナ用ドライバ・ソフトウェア ダウンロード|GRAPHTEC

Page 77 8 Clicking the [OK] button begins calibration. Click graphtec cs500 Close button. If there is no discrepancy, color correction is complete.